Senin, 12 November 2012

Echo Boss Clock widget for Bada

 
This widget is supported on the following Samsung phones:
  • Wave S8500 (Bada 2.0)

Download and install - Update Galaxy s3 Root on XXDLIH Jellybean 4.1 Firmware

S3 Logo 
Procedure to Root Galaxy S3 on XXDLIH Jellybean 4.1 Firmware:
  • Download Odin and XXDLIH Rooting Package from here to your computer. Once downloaded, you now need to extract the rooting package and Odin in your computer.
  • Open odin in your computer and turn off your phone so that it can be entered in the Download Mode.
  • Download Mode in Galaxy S3 can be entered by pressing the Volume Down rocker key + power button at the same time while the device is turned Off. If the device starts in the normal mode, you need to re try the process of the entering the device into the download mode. Refer below video on how to enter your Galaxy S3 in the Download Mode.
  • Click on “PDA” to select “CF-Root-SGS3-v6.4.tar” and then click on “Start”. Once you click on start, it will take around 2 – 3 minutes for rooting the device. Please note that once the device is rooted, the device will be rebooted automatically.
  • You can now disconnect the device and check whether the device is rooted or not. To check on whether your device is rooted or not, you will have to download the “Root Checker” app from the Google PLAY Store. If your device is not rooted, you will have to follow the instructions mentioned above for rooting your Galaxy S3.
Note: If the device gets into the boot loop sequence or say gets stuck in the welcome screen, just re insert the battery and re follow the above instructions so as to again follow the above mentioned instructions.
We just hope that by following the above mentioned procedure, you were able to root the device, just in case if you were not able to root, all you need to do is to just report to us in the comments section so that we can then take up in a priority manner. Congrats, you have now successfully rooted your Galaxy S3 and you are now ready to install custom ROM firmwares.

Minggu, 11 November 2012

Need for Speed™ Most Wanted for Android - apk game

 
 
  
Do you dare to be the Most Wanted?
“The graphics are absolutely awesome” (Eurogamer.es)
“It pushes the mobile platform to its utmost limits and doesn’t even break a sweat” (Capsule Computers)
Buckle up, hit the gas and hold on tight; you’re in for the ride of your life. Outrun cops, outsmart rivals – and outdrive your friends – in the most dangerous Need for Speed yet. Do you dare to be the Most Wanted?
** Need for Speed™ Most Wanted is an immersive, high quality game that requires a 550MB+ download. To speed things up, we recommend connecting to WiFi.**
MAKE TROUBLE, GET WANTED
Evade a relentless police force while you clash with street racers. Race and chase hot cars like the SRT Viper GTS, Porsche 911 Carrera S, Hummer H1 Alpha, and many more. Feel the intensity of no-brakes-allowed street racing with realistic full-car damage for the first time on mobile.
LEAVE YOUR MARK
Log into Origin to check the Wanted List and find out who is the Most Wanted across platforms and among your friends. Then, challenge your friends and prove your racing skills in nonstop competition.
GO FROM ZERO TO MOST WANTED…
• Drive and customize over 35 of the world’s most exciting cars
• Race the way you want! By popular demand, you can now touch or tilt to steer
• Use Mods to enhance your car and get ahead of the pack in style
• Experience the action with mind-blowing graphics and intense full-car damage
• Earn Speed Points to unlock new cars
Your rivals will do everything they can to stop you from getting to the top – but in this world, there can only be one Most Wanted.


SD Data : Android/Data
Mali :
http://adf.ly/Efg36

Jumat, 09 November 2012

Download and install - Update Galaxy Note N7000 Root on XXLS2 Jellybean 4.1.2 Firmware

Galaxy Note Logo 
Tutorial to Root Samsung Galaxy Note N7000 on Jellybean 4.1 XXLS2 Firmware:
  • Download the Rooting Package and Odin from here to your computer. Once downloaded, extract both the zip files in your computer to Open Odin in your computer.
  • Turn Off your Galaxy Note so that it can be entered in the download mode. The download mode can be entered by pressing Volume Down Key + OK button, and holding both simultaneously press the Power Button. Just in case if the device turns ON in the normal mode, you will have to again retry entering the device in the download mode.
  • Now, connect your Note N7000 to the computer with the help of original USB cable after which you will see that the ID : COM section will turn Yellow indicating that all the drivers are OK and you can now proceed to next step.
  • Click on “PDA” to select the tar file which you will get after extracting the rooting package in odin to click on “Start”. As soon as the rooting process is completed, the device will be rebooted. The whole process of rooting will tase around 3 – 4 minutes, in some case it may take longer time as well.
  • To check on whether your device is rooted or not, you will have to download the “Root Checker” app from the Google PLAY Store. Just in case if the device is not rooted, you will have to re follow the instructions.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Congratulations, you have now successfully rooted your Galaxy note N7000 on Jellybean 4.1 XXLS2 Firmware.

Download and install - Update Galaxy Note 10.1 N8000 with Official Jellybean 4.1 XXBLJ9 Firmware

Galaxy Note 10.1 
Procedure to Update Galaxy Note N8000 10.1 tablet with XXBLJ9 Jellybean 4.1 firmware:
  • Open odin in your computer and turn Off your tablet so that it can be entered in the Download Mode.
  • Now, hold Volume Down rocker key and holding this press the Power button till you see the Warning Screen. Now, on WARNING Screen you will have to press the Volume Up key to enter the device in the download mode.
  • In download mode, connect your device to the computer with the help of original USB cable and select the “N8000XXBLJ9_N8000OXABLJ9_412156_REV00_user_low_ship.tar.md5” file in “PDA” in Odin. Once the file is selected, click on “Start” to commence the process of firmware update.
  • As soon as the firmware is updated successfully, you now need to wait for the device to show the country selector after which you can disconnect the device connected with computer. The whole process of firmware update may take around 7 – 10 minutes. Also, once the update is applied, the device will take longer time than usual for booting the device.
  • To check whether your phone is updated or not, head over to the path “Settings > About Phone” where you will get to see the firmware version as Jellybean 4.1 XXBLJ9.
Users Facing Force Close Issues:
Turn Of your Galaxy Note N8000 to enter your device in the recovery mode. In the recovery mode select Wipe data/factory reset and also you need to select Wipe Cache partition and then reboot your device by selecting reboot system now option.
Note: just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do let us know in the comments section or on our facebook page / Google + Page if you come across with any issues faced in the process of applying this update as we will try address the same at the earliest. So there you go, you have now successfully learnt on how to apply this firmware update. We will soon come up with an article which will help you to root your Galaxy note N8000 on XXBLJ9 firmware and also on how to update Galaxy Note 10.1 N8000 with Jellybean 4.2 firmware.

Download and install - Update Galaxy Note N7000 with Official Jellybean 4.1.1 XXLS2 Firmware

Galaxy NOTE RED Logo 
Procedure to Update Galaxy Note N7000 with Jellybean 4.1.1 XXLS2 Firmware:
  • Now, open Odin in your computer and turn off your Galaxy Note N7000 so that it can be entered in the download mode. The download mode can be entered by pressing Volume Down Key + OK button, and holding both simultaneously press the Power Button. Just in case if the device turns ON in the normal mode, you will have to again retry entering the device in the download mode.
  • Once your Galaxy Note N7000 enters in download mode, connect your phone to the computer with the help of original USB cable while keeping Odin opened and then you will see that the ID : COM section will turn Yellow which will indicate that all drivers are installed.
DANGER: Don’t proceed to the next step if the ID: COM Section doesn’t turn Yellow!
  • Now, click on “PDA” to select the tar file which you get after extracting the firmware file. Ignore the .dll file which you get after extracting the folder. Once selected, click on “Start” in odin to start the process of firmware update.
  • As soon as the firmware is update, the device will reboot and once you see the country selector, disconnect the phone from computer to follow on screen instructions for setting up the phone. To check whether your phone is updated or not, head over to the path “Settings > About Phone” where you will get to see the firmware version as Jellybean 4.1.1 XXLS2.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
For Users Facing Force Close Issues:
  • If at all your device is facing issues like force close issues in most of the apps, you will now have to turn off the device and clear the cache from the recovery mode.
  • Recovery mode can be entered by pressing Center button and simultaneously press the Power Button. In the recovery mode select Wipe data/factory reset and also you need to select Wipe Cache partition and then reboot your device by selecting reboot system now option.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Congratulations, you have now successfully applied the latest firmware update of Jellybean 4.1 in your Galaxy Note N7000 smartphone.

Download and install - Update Samsung Galaxy Nexus – Steps to Manual Update with Factory Jellybean 4.1.2 JZO54K Firmware

Galaxy Nexus Logo 
Procedure to Manual Update Galaxy Nexus with Stock Jellybean 4.1.2 Firmware:
  • Once placed the file, you need to open the Command prompt in your computer to enter the command as mentioned below,
Adb devices
Adb reboot bootloader
  • Now, press Volume Up button to see the option of “Recovery Mode” and then press the power button to enter into the same. Alternatively, you can also enter your Nexus in the recovery mode by pressing the “Volume Up + Volume Down” button simultaneously and keeping holding these two buttons you need to press the power button. Ensure that you will have to turn off the device before performing the manual step of entering into recovery.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition” and then select “install zip from sd card”> “choose zip from internal sd card” to select the Jellybean 4.1.2 Firmware Package which you have placed in your device. Once the firmware is applied successfully, you will then get to see a message “install from sd card complete”. So, once the firmware is updated successfully select “go back” and choose the option of reboot system now.
  • To check on whether the firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where you will find the firmware version as Jellybean 4.1.2.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Very soon we will be coming out with a new article which will help you to update with the latest Jellybean 4.2 version of firmware. Stay tuned to Android Advices.

Download and install - Update Galaxy Note N7000 – Stylish Jellybean 4.1.2 Paranoid Firmware

note 2 nEW 2 
Procedure to Update Galaxy Note N7000 with Paranoid custom ROM firmware:
  • Download the 4.1.2 Paranoid Custom ROM Firmware Package and Google Apps Package from here to your computer. Once downloaded, connect your Galaxy Note N7000 with the help of original USB cable and place these two zip files in your Galaxy Note. Ensure that you are not placing the zip file deep into the sub folders.
  • Once the zip file is placed, disconnect the device and download the “ROM Manager” app from the PLAY Store. Please note that you should not backup the data with this app as it may brick your Galaxy Note. Now, either with the help of ROM Manager app you can enter the device in the recovery mode or with the help of below mentioned manual step you can easily enter the device in the recovery mode.
  • Hold the Volume Up button + the Home key button (the middle button) and while holding these both keys, press the Power button for turning the device ON in the recovery mode in your Galaxy Note.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. Also, select “advanced” and clear the Dalvik cache too if you are on the custom ROM firmware.
  • Up next select “install zip from sd card” to select the placed paranoid custom ROM firmware and the Google Apps Package. Once the firmware is completed, the screen will read as “install from sd card complete” after which you need to select “go back” and then “reboot system now” for rebooting the device in the normal mode.
  • To check on whether the Paranoid custom ROM firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where you will find the firmware version as jellybean 4.1.2 and Paranoid.
Note: just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Congrats you have successfully updated your device with the latest Paranoid custom ROM firmware, we will very soon be coming up with the Official Jellybean 4.1.2 firmware for Galaxy Note N7000, so stay tuned for more updates.

Download and install - Update Galaxy S I9000 with Jellybean 4.1.2 C-RoM Mix v5.0 Firmware

Jellybean 4.1 Logo 
Procedure to Update Samsung Galaxy S GT I9000 with C-RoM Mix v5.0 firmware:
  • Download the C-RoM Mix v5.0 firmware package from here to your computer. Once downloaded, connect your Galaxy S GT I9000 to the computer with the help of original USB cable and place the zip file into the sd card. Ensure that you are not placing the files deep into the sub folders.
  • Recovery mode in Galaxy S GT I9000 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. You can also enter the device in recovery mode via the ROM Manager app.
  • Now, in the recovery mode, select “install zip from sd card” > “choose zip from internal sd card” and then choose the C-RoM Mix v5.0 firmware  Package. It will take around 4 -5 minutes for applying the update.
  • Once you see the “install from sd card complete” message on screen, select “Go Back” and select “reboot system now” for rebooting the device in the normal mode.
  • To check on whether the C-RoM Mix v5.0 firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where you will find the firmware version.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Congratulations, you have now successfully learnt to update your Galaxy S with C-RoM Mix v5.0 firmware, in the coming days to come we will come with new custom Jellybean 4.2 firmwares for Galaxy S devices.

Selasa, 06 November 2012

Download and install - Update Verizon Wireless Galaxy S3 with ULE based Clean ROM Jellybean 4.1.1 Firmware

S3 Vzw Logo 
Procedure to Update VZW Galaxy S3 with Jellybean 4.1.1 Clean ROM Firmware:
  • Disconnect the device and turn off the device so that it can be entered in the recovery mode. Recovery mode in Galaxy S2 GT I9100 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device. In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode.
  • Alternatively, you can also enter the device into recovery mode with the help of ROM Manager app. Now, in recovery mode select “install zip from sd card” > “choose zip from internal sd card” and then choose the Android revolution custom ROM firmware Package
Note: If the device gets into the boot loop sequence or say gets stuck in the welcome screen, just re insert the battery and re follow the above instructions so as to again follow the above mentioned instructions.
To check on whether the firmware has been successfully applied or not, all you need to do is to just head over to the path “Settings > About Phone” where in you can check the same on the firmware has been updated or not. Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same.

Download and install - Update Galaxy S2 GT I9100 – Steps to Update with Jellybean 4.2 Custom ROM Firmware

S2 New logo 
Procedure to Update Jellybam 4.2 Update in GALAXY S2 GT I9100:
  • Download the Jellybam 4.2 Firmware Package from here to your computer. Once downloaded, connect your device to the computer with the help of original USB cable and place the zip file in your device.
  • Once you have placed the file, disconnect the device and turn off your device so that it can be entered in the recovery mode.
  • Recovery mode in Galaxy S3 GT I9100 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. You can also enter the device in recovery mode alternatively via the ROM Manager app which can be downloaded from the Google PLAY Store.
  • Now, in the recovery mode, select “install zip from SD Card” to select the zip file of Jellybam which you have placed in your device’s SD Card. Once the file is selected, you now need to wait for the zip file to get processed in the device. As soon as you see the message of “installing from sd card completed” at the bottom of the screen, you now need select “go back” and then select “reboot system now” for rebooting the device in the normal mode. Device will take longer time than expected for rebooting the device.
Note: If the device gets into the boot loop sequence or say gets stuck in the welcome screen, just re insert the battery and re follow the above instructions so as to again follow the above mentioned instructions.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. To check on whether the update has been successfully applied or not, you need to check the same from the path “Settings > About Phone” where you will find the current firmware version as Jellybean 4.1.2 firmware.

Download and install - Update Galaxy S3 I9300 with Capon Mod Jellybean 4.1.2 Custom ROM Firmware

GALAXY S3 HUGE 
Procedure to Update Galaxy S3 GT I9300 with Jellybean 4.1.2 firmware based Capon ROM:
  • Download the Capon ROM firmware zip Package from here to your computer. Once downloaded, connect your phone to the computer with the help of original USB cable and place this zip file in your device’s external SD Card.
  • Now, disconnect the Galaxy S3 connected to your computer and turn Off your device so that it can be entered in the recovery mode.
  • Recovery mode in Galaxy S3 GT I9300 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. You can also enter the device in recovery mode via the ROM Manager app.
  • Select “install zip from sd card” > “choose zip from internal sd card” to select the Capon ROM Custom ROM Firmware Package which you have placed in your device. Once selected, it will take around 4 – 7 minutes for applying the update. As soon as the update is applied successfully, select “go back” and “reboot system now” for rebooting the device in the normal mode.
  • For your phone to show the home screen, it might take longer than expected time as it is the first time after installing the firmware update.
  • Once the update is applied, select the option of “Go Back” and “Reboot System now” for rebooting the device in the normal mode. Since it’s a first reboot, it will take more time than the normal mode as it has to finalize all the apps etc.
Note: If the device gets into the boot loop sequence or say gets stuck in the welcome screen, just re insert the battery and re follow the above instructions so as to again follow the above mentioned instructions.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. So there you go you have now successfully learnt on how you can upgrade your Samsung Galaxy S3 GT I9300 with the Capon Mod custom ROM.

Kamis, 01 November 2012

Download and install - Update Galaxy ACE S5830 with Most Popular APOCALYPSE Custom ROM Firmware

ACE 8 
  • ICS-Style Settings Menu
  • modded ICS Transparent Theme
  • centered clock
  • status bar supports transparency
  • 50% trans-black lockscreen styles (sliding tabs, rotary, lens)
  • bubble locksreen style by Team Carbon/Steel Blue Theme
  • blue lockscreen buttons by Team Carbon/Steel Blue Theme
  • contacts list image by Team Carbon/Steel Blue Theme
  • usb mount image by Team Carbon/Steel Blue Theme
  • sansation font  
 Procedure to Update Galaxy ACE S5830 with APOCALYPSE Custom ROM Firmware:
  • Download the APOCALYPSE firmware package from here to your computer. Once downloaded, connect your device to the computer with the help of original USB cable and place the downloaded zip file in your Galaxy ACE.
  • Once you have placed the same, turn off the device so that it can be entered in the recovery mode. To enter Galaxy ACE S5830 in the recovery mode, download the ROM Manager app and select the option of “reboot into recovery mode”.
  • Once the device boots in the recovery mode, select “install zip from sd card” > “choose zip from sd card” and select the APOCALYPSE Custom ROM Firmware package which you have placed in your device.
  • Please note that once the file is selected, it will take around 4 – 5 minutes for applying this update and once it’s placed, you will need to select “Go Back”
Tip: If your Galaxy ACE doesn’t power up or say it gets into the boot loop mode, you need to re insert the battery and then re try the process of firmware update by following the above steps.
So there you go you have now successfully updated your device with the latest APOCALYPSE custom ROM firmware. Do share with us in the comments section below just in case if you face any issues as we will try our level best to sort out the same. To check whether your phone is updated or not, head to the path “Settings > About Phone” where you will get to see the firmware as APOCALYPSE.